Harken Rollpin replacement kit Instrukcja Użytkownika Pobierz pdf (Strona 1)

INSTRUCTION SHEET

Jib Reefing & Furling

Rollpin Replacement Kit

1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.

Telephone: (262) 691-3320 • Fax: (262) 691-3008

Web: http://www.harken.com • E-mail: [email protected]

Rollpins Paper Towels

Loctite

277 (Red) Hammer

Wood Support Block Center Punch

Flushing Punch Vice-Grip-type pliers

Loctite

Primer “N” (HFG395) Rollpin Punch (available from Sears:

/32” for #1,

/8" for #2)

Supplies Included Supplies You Need

Checking Joints

1. Take headstay down and remove lower drum assembly and feeder.

2. Recess threaded stud into bottom foil to allow room on wire to take

joints apart for re-gluing. If you have a Norseman

, Sta-lok

or Navtec

terminal, take bottom joint apart as directed below to allow space on

wire to separate foils.

3. Support joint area in the Wood Support Block (included). Use a Roll

Pin Punch to drive pin out or pound new rollpin half-way into foil, to

push old pin out half-way.

4. Pull both pins out of foil using vice-grips or pliers.

5. Try pulling foil sections apart. If they come apart, foils need

to be re-glued to connectors.

Continued

INSTRUCTION SHEET

Jib Reefing & Furling

Rollpin Replacement Kit

1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.

Telephone: (262) 691-3320 • Fax: (262) 691-3008

Web: http://www.harken.com • E-mail: [email protected]

Rollpins Paper Towels

Loctite

277 (Red) Hammer

Wood Support Block Center Punch

Flushing Punch Vice-Grip-type pliers

Loctite

Primer “N” (HFG395) Rollpin Punch (available from Sears:

/32” for #1,

/8" for #2)

Supplies Included Supplies You Need

Checking Joints

1. Take headstay down and remove lower drum assembly and feeder.

2. Recess threaded stud into bottom foil to allow room on wire to take

joints apart for re-gluing. If you have a Norseman

, Sta-lok

or Navtec

terminal, take bottom joint apart as directed below to allow space on

wire to separate foils.

3. Support joint area in the Wood Support Block (included). Use a Roll

Pin Punch to drive pin out or pound new rollpin half-way into foil, to

push old pin out half-way.

4. Pull both pins out of foil using vice-grips or pliers.

5. Try pulling foil sections apart. If they come apart, foils need

to be re-glued to connectors.

Continued

INSTRUCTION SHEET

Jib Reefing & Furling

Rollpin Replacement Kit

1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.

Telephone: (262) 691-3320 • Fax: (262) 691-3008

Web: http://www.harken.com • E-mail: [email protected]

Rollpins Paper Towels

Loctite

277 (Red) Hammer

Wood Support Block Center Punch

Flushing Punch Vice-Grip-type pliers

Loctite

Primer “N” (HFG395) Rollpin Punch (available from Sears:

/32” for #1,

/8" for #2)

Supplies Included Supplies You Need

Checking Joints

1. Take headstay down and remove lower drum assembly and feeder.

2. Recess threaded stud into bottom foil to allow room on wire to take

joints apart for re-gluing. If you have a Norseman

, Sta-lok

or Navtec

terminal, take bottom joint apart as directed below to allow space on

wire to separate foils.

3. Support joint area in the Wood Support Block (included). Use a Roll

Pin Punch to drive pin out or pound new rollpin half-way into foil, to

push old pin out half-way.

4. Pull both pins out of foil using vice-grips or pliers.

5. Try pulling foil sections apart. If they come apart, foils need

to be re-glued to connectors.

Continued

INSTRUCTION SHEET

Jib Reefing & Furling

Rollpin Replacement Kit

1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.

Telephone: (262) 691-3320 • Fax: (262) 691-3008

Web: http://www.harken.com • E-mail: [email protected]

Rollpins Paper Towels

Loctite

277 (Red) Hammer

Wood Support Block Center Punch

Flushing Punch Vice-Grip-type pliers

Loctite

Primer “N” (HFG395) Rollpin Punch (available from Sears:

/32” for #1,

/8" for #2)

Supplies Included Supplies You Need

Checking Joints

1. Take headstay down and remove lower drum assembly and feeder.

2. Recess threaded stud into bottom foil to allow room on wire to take

joints apart for re-gluing. If you have a Norseman

, Sta-lok

or Navtec

terminal, take bottom joint apart as directed below to allow space on

wire to separate foils.

3. Support joint area in the Wood Support Block (included). Use a Roll

Pin Punch to drive pin out or pound new rollpin half-way into foil, to

push old pin out half-way.

4. Pull both pins out of foil using vice-grips or pliers.

5. Try pulling foil sections apart. If they come apart, foils need

to be re-glued to connectors.

Continued

1 2

Podsumowanie treści

Strona 1

INSTRUCTION SHEETJib Reefing & Furling Rollpin Replacement Kit1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.Telephone: (262) 691-3320 • Fa

Strona 2

Printed in USA. 4884/2-05Gluing JointsIf furling system has been stored in a horizontal position, make sure inside of foils are dry. If they are wet,

Komentarze do niniejszej Instrukcji

Brak uwag

Harken Rollpin replacement kit Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Harken Rollpin replacement kit. Harken Rollpin replacement kit User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Harken Rollpin replacement kit Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Harken Rollpin replacement kit. Harken Rollpin replacement kit User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Harken Rollpin replacement kit